sidactor ? protection thyristors 118 revised: february 22, 2011 ? 2011 littelfuse, inc. speci?cations are subject to change without notice. please refer to www.littelfuse.com for current information. slic protection battrax ? series - single port negative - ms-013 1 3 2 5 (t) (-v ref ) (r) (g) 6 (no connect) 4 (no connect) electrical characteristics the battrax ? series offers programmable sidactor ? overvoltage protection devices for slic applications. the single port negative battrax series provides a programmable device that is referenced to a negative voltage souce while internal diodes provide protection from positive surge events. description agency approvals agency agency file number e133083 schematic symbol pinout designation features and bene?ts t low voltage overshoot t low on-state voltage t does not degrade with use t fails short circuit when surged in excess of ratings t single-port protection t gate triggered tracking device t integrated diodes for positive voltage part number marking v drm @l drm =5a v s @100v/s i h i s i t v t @i t =2.2 amps v f capacitance* v min v max ma min ma max a max v max v max pf min pf max b1101uclxx b1101uc i-v ref * * 7 * i-v ref * * 7 * 100 100 2.2 4 5 30 200 b1161uclxx b1161uc i-v ref * * 7 * i-v ref * * 7 * 160 100 2.2 4 5 30 200 b1201uclxx b1201uc i-v ref * * 7 * i-v ref * * 7 * 200 100 2.2 4 5 30 200 1 2 3 6 5 4 applicable global standards t tia-968-a t tia-968-b t itu k.20/21 enhanced level t itu k.20/21 basic level t gr 1089 inter-building t gr 1089 intra-building t iec 61000-4-5 t yd/t 1082 t yd/t 993 t yd/t 950 notes: - absolute maximum ratings measured at t a = 25oc (unless otherwise noted). - devices are uni-directional - all electrical characteristics shown are de?ned from tip (pin 1) to ground (pin 5), and ring (pin 3) to ground (pin 5) - v ref max value for the negative battrax is -200 v. - xx = part number suf?x: tp (tube pack) or rp (reel pack). * off-state capacitance (c o ) is measured across pins 1 & 5 and 3 & 5 at 1 mhz with a 2v bias.
sidactor ? protection thyristors 119 revised: february 22, 2011 ? 2011 littelfuse, inc. speci?cations are subject to change without notice. please refer to www.littelfuse.com for current information. slic protection i h i drm v drm v t +v +i v s i s i t v -v -i i f v ref i pp pin 1-2: pin 2 connected to ground pin 3 connected to v ref surge ratings series i pp i tsm 50/60 hz di/dt 0.2x310 1 0.5x700 2 2x10 1 2x10 2 8x20 1 1.2x50 2 10x160 1 10x160 2 10x560 1 10x560 2 5x320 1 9x720 2 10x360 1 10x360 2 10x1000 1 10x1000 2 5x310 1 10x700 2 a min a min a min a min a min a min a min a min a min a min a/s max c 50 500 400 200 150 200 175 100 200 50 500 package symbol parameter value unit modi?ed ms-013 1 2 3 6 5 4 t j operating junction temperature range u p c t s storage temperature range u p c r 0 ja thermal resistance: junction to ambient 60 c/w thermal considerations 50 100 0 t r t d 0 peak value half value t C time (s) i pp C peak pulse current C %i pp t r = rise time to peak value t d = decay time to half value waveform = t r x t d v-i characteristics t r x t d pulse waveform 25c case temperature (t c ) - oc 2.0 1. 8 1. 6 1. 4 1. 2 1. 0 0.8 0.6 0.4 -40 -20 0 20 40 60 80 100 120 140 160 ratio of i h i h (t c = 2 5 oc) normalized v s change vs. junction temperature normalized dc holding current vs. case temperature pin 5 connected to ground pin 2 connected to v ref -8 -40 -20 0 20 40 60 80 100 120 140 160 -6 -4 0 2 4 6 8 10 12 14 junction temperature (t j ) C c percent of v s change C % 2 5 c notes: 1 current wavef orm in s 2 voltage wavef orm in s - peak pulse current rating (i pp ) is repetitive and guaranteed for the life of the product. - i pp s b u j o h t b q q m j d b c m f p w f s u f n q f s b u v s f s b o h f p g ? $ u p ? $ * pp rating assumes v ref f r v b m t 7 - the device must initially be in thermal equilibrium with -40c < t j < ? $
sidactor ? protection thyristors 120 revised: february 22, 2011 ? 2011 littelfuse, inc. speci?cations are subject to change without notice. please refer to www.littelfuse.com for current information. slic protection part numbering b1 xx 1 u c l xx type holding current package type i pp rating rohs compliant construction variable packing options rp: reel pack tp: tube pack b1: negative battrax sidactor 10: 100 ma 16: 160 ma 20: 200 ma physical speci?cations lead material copper alloy terminal finish 100% matte-tin plated body material ul recognized epoxy meeting ?ammability classi?cation 94v-0 time temperature t p t l t s(max) t s(min) 25 t p t l t s time to peak temperature (t 25oc to peak) ramp-down ramp-up preheat critical zone t l to t p figure 1 soldering parameters environmental speci?cations part marking high temp voltage blocking 80% rated v ref max. (v dc peak
|